LizardFS Hypervisors and Virtualization Cookbook¶
Providing storage for XenServer¶
LizardFS >= 3.10.4 XenServer >= 7
XenServer 7 is required since it makes use of CentOS 7 as the underlying OS and LizardFS provides packages for CentOS 7.
Installing 3rd party components – such as the LizardFS client, and server components may invalidate any support provided by Citrix for your installation.
This guide presumes you have already installed XenServer – and are familiar with accessing the XenServer Console and using tools such as ‘vi’ to edit files.
You should have already configured the networking on XenServer. This could be just a single network – XenServer installations usually have an ‘INTERNET facing’ network – and then one, or more ‘storage networks’ – make sure IP addresses are setup that you can use for connecting to, or running LizardFS on (i.e. probably not INTERNET facing).
Preparing Storage – if you need it¶
If you are going to use the XenServer itself to provide storage – you’ll need to prepare drives / directories on the server.
As an example - we’ll mount all the drives we want to place chunks on under ‘/mnt’. Once XenServer is booted – from the XenServer console you can see a list of available drives by looking in ‘/dev/disk/by-id’ – i.e.
[root@XenServer-1 ~]# ls -l /dev/disk/by-id/ total 0 lrwxrwxrwx 1 root root 9 Mar 22 15:48 ata-Crucial_CT250MX200SSD1_153710904260 -> ../../sdi lrwxrwxrwx 1 root root 9 Mar 22 15:48 ata-Crucial_CT250MX200SSD1_154110CAA644 -> ../../sdh lrwxrwxrwx 1 root root 9 Mar 22 15:48 ata-SAMSUNG_HD204UI_S2H7J1CZ909998 -> ../../sdf lrwxrwxrwx 1 root root 9 Mar 22 15:48 ata-SAMSUNG_HD204UI_S2H7J1CZ910008 -> ../../sde
By using the ‘/dev/disk/by-id’ entries we ensure if the disk is moved to another bay – it will still mount correctly. You can use ‘gpart’ to partition these disks, or just use the “raw” disk to create partitions on, e.g.:
mkfs.ext4 /dev/disk/by-id/ata-Crucial_CT250MX200SSD1_153710904260 mkfs.ext4 /dev/disk/by-id/ata-Crucial_CT250MX200SSD1_154110CAA644 mkfs.ext4 /dev/disk/by-id/ata-SAMSUNG_HD204UI_S2H7J1CZ909998 mkfs.ext4 /dev/disk/by-id/ata-SAMSUNG_HD204UI_S2H7J1CZ910008
And so on, for all the drives you want to use.
Once you’ve formatted the disks – we need to tell XenServer where to mount them when the system comes up. First you need to create directories under the ‘/mnt’ directory – if you keep the name of the directory the same as the drive device name, we’d do:
mkdir /mnt/ata-Crucial_CT250MX200SSD1_153710904260 mkdir /mnt/ata-Crucial_CT250MX200SSD1_154110CAA644 mkdir /mnt/ata-SAMSUNG_HD204UI_S2H7J1CZ909998 mkdir /mnt/ata-SAMSUNG_HD204UI_S2H7J1CZ910008 chown mfs:mfs /mnt/ata-*
Once this is done you can add the drives to the systems ‘fstab’ to ensure they are mounted automatically at boot-time – if you ‘vi /etc/fstab’ and then create entries such as:
/dev/disk/by-id/ata-Crucial_CT250MX200SSD1_153710904260 defaults,nofail 0 2 /dev/disk/by-id/ata-Crucial_CT250MX200SSD1_154110CAA644 defaults,nofail 0 2 /dev/disk/by-id/ata-SAMSUNG_HD204UI_S2H7J1CZ909998 ext4 defaults,nofail 0 2 /dev/disk/by-id/ata-SAMSUNG_HD204UI_S2H7J1CZ910008 ext4 defaults,nofail 0 2
The ‘nofail’ option means that the system continues to boot even if the disk or disks are unavailable. Once this is done you can mount all of those disks with:
Before you can install any of the LizardFS components we need to tell the XenServer nodes where to get the LizardFS RPM’s from.
For each node in the system (or any nodes you add) you need to log in to the XenServer console on the node and run once:
curl http://packages.lizardfs.com/yum/el7/lizardfs.repo > /etc/yum.repos.d/lizardfs.repo
This fetches the LizardFS repository details to somewhere XenServer can find them (with the ‘yum’ command).
To connect XenServer to LizardFS you need to install the ‘lizardfs-client’. Even if you’re not installing full LizardFS on XenServer you still need to install the client package as well as the FUSE library package.
The repo file XenServer points to packages that are no longer present on the CentOS site (they’ve been moved to the CentOS ‘Vault’) – so we need to adjust the URL so the system can pull in FUSE as part of the ‘lizardfs-client’ install.
Edit the file ‘/etc/yum.repos.d/CentOS-Base.repo’ – change the “[base]” URL to read:
And save the file.
We can now install ‘lizardfs-client’ (which will also install FUSE) with:
yum --disablerepo=extras --disablerepo=updates install lizardfs-client
If you’re just using XenServer to access another LizardFS installation (i.e. on another server / system) you don’t need to add the following other software components – just skip ahead to Client Configuration .
LizardFS Chunk-Server and Meta-Server¶
If you’re using the XenServer as either a ‘chunk-server’ (holds data) or ‘meta-server’ (holds meta-data) you’ll need to install other components of LizardFS on the XenServer as well.
You can use the following to install the ‘master’ server (meta-server), chunkserver – and Admin tools respectively:
yum --disablerepo=base --disablerepo=extras --disablerepo=updates install lizardfs-master yum --disablerepo=base --disablerepo=extras --disablerepo=updates install lizardfs-chunkserver yum --disablerepo=base --disablerepo=extras --disablerepo=updates install lizardfs-adm
Setting up the Chunk Server¶
By now you should have the LizardFS chunk-server software installed – and your drives setup ready to hold data chunks. The LizardFS chunk-server installs with a default config – but you need to copy it into place first:
cd /etc/mfs cp mfshdd.cfg.dist mfshdd.cfg
You’ll need to edit ‘/etc/mfs/mfshdd.cfg’ to tell the chunk-server what drives it has available. For our example we edited ‘mfshdd.cfg’ and added:
# Our Chunk Drives/Directories /mnt/ata-Crucial_CT250MX200SSD1_153710904260 /mnt/ata-Crucial_CT250MX200SSD1_154110CAA644 /mnt/ata-SAMSUNG_HD204UI_S2H7J1CZ909998 /mnt/ata-SAMSUNG_HD204UI_S2H7J1CZ910008
Setting up the Meta Server (‘master’)¶
If you’re running the master / meta-server under XenServer you need to make one node a ‘master’ and the other a ‘shadow’. You will need to copy the example configs to the real configuration files:
cd /etc/mfs cp mfsmaster.cfg.dist mfsmaster.cfg cp mfsexports.cfg.dist mfsexports.cfg
You need to edit ‘/etc/mfs/mfsmaster.cfg’ one (and only one) node should have a personality of ‘master’ – the other should be a ‘shadow’. It is also recommended in that file that you set an ‘ADMIN_PASSWORD’. If the XenServer is going to be running as a master, or shadow – you’ll also need to edit ‘/etc/mfs/mfsexports.cfg’ – by default this just sets up a basic config (this is similar to an nfs exports file). Finally – you’ll need to install a blank database for the ‘master’ server – and any shadows – this involves copying an empty database i.e.:
cp /var/lib/mfs/metadata.mfs.empty /var/lib/mfs/metadata.mfs chown mfs:mfs /var/lib/mfs/metadata.mfs
You will only need to do this when installing the ‘master’ service.
XenServer ships with a firewall – we’ll need to configure that to allow LizardFS traffic to pass. To do this edit ‘/etc/sysconfig/iptables’ – we need to add our rules before the REJECT line and COMMIT statement so you should end up with:
# LizardFS -A RH-Firewall-1-INPUT -m conntrack --ctstate NEW -m tcp -p tcp --dport 9421 -j ACCEPT -A RH-Firewall-1-INPUT -m conntrack --ctstate NEW -m tcp -p tcp --dport 9422 -j ACCEPT -A RH-Firewall-1-INPUT -m conntrack --ctstate NEW -m tcp -p tcp --dport 9420 -j ACCEPT -A RH-Firewall-1-INPUT -m conntrack --ctstate NEW -m tcp -p tcp --dport 9419 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT
You must now restart the firewall service with:
service iptables restart
LizardFS requires the host name ‘mfsmaster’ to resolve and point to the IP of the master server. The easiest way to achieve this is to edit ‘/etc/hosts’ – and add an entry for it:
The ‘192.168.0.100’ IP address should be the IP address of a LizardFS ‘master’ server (not shadow). If you’re running XenServer with an existing LizardFS system on other hosts – you should already have a ‘master’ server. If you’re running LizardFS master service on XenServer it’ll be the IP of whichever node you setup as ‘master’ (not ‘shadow’).
If you are running an HA setup of LizardFS it should be the “URAFT_FLOATING_IP” you defined in your URAFT configuration.
Assuming you installed the LizardFS admin tools – you can make life easier by adding the following lines to ‘/root/.bashrc’:
alias lfschunks='lizardfs-admin list-chunkservers mfsmaster 9421' alias lfshealth='lizardfs-admin chunks-health mfsmaster 9421' alias lfsmounts='lizardfs-admin list-mounts mfsmaster 9421' alias lfsdisks='lizardfs-admin list-disks mfsmaster 9421'
Once the service has started we can use these aliases / commands to check on things (if you haven’t installed the LizardFS admin tools and want to use these commands – see above for info on how to install them).
Testing your LizardFS setup¶
If you’re connecting XenServer to an existing LizardFS system – you should be able to just mount the LizardFS at this point, e.g.:
mkdir /mnt/lizardfs mfsmount /mnt/lizardfs
This should mount the LizardFS file system under ‘/mnt/lizardfs’. If it’s an existing system you’ll need to make sure you mount at the correct point (i.e. check how the existing system is setup).
If you’re running LizardFS on the actual XenServers we’ll need to bring up the ‘master’ service – and the chunk- servers. You can do this with:
service lizardfs-master start service lizardfs-chunkserver start
You’ll need to repeat this on each node – remembering only one can be the ‘master’ meta-server – the other has to be a shadow (set in ‘/etc/mfs/mfsmaster.cfg) You should then be able to mount the default LizardFS then with:
mkdir /mnt/lizardfs mfsmount /mnt/lizardfs
This should be repeated on each node.
Once that’s done – if you’ve installed the LizardFS admin tools (and added the above Bash aliases) you can use:
lfshealth - Display info on the 'health' of the LizardFS lfsmounts - Display info on what's mounted the LizardFS file system lfsdisks - Display info on all the disks provided by the chunk-servers on the system lfschunks - Display info on the chunk-servers on the system
As a quick test – if you create a test-file in ‘/mnt/lizardfs’ on one node – the other should show it, i.e.:
[root@XenServer-1 ~]# cd /mnt/lizardfs [root@XenServer-1 lizardfs]# echo “Hello World!” >/mnt/lizardfs/test.txt
(switch to XenServer-2 Console)
[root@XenServer-1 ~]# cd /mnt/lizardfs [root@XenServer-2 lizardfs]# cat test.txt Hello World! [root@XenServer-2 lizardfs]#
At this point we can create a ‘xen-sr’ directory – and set a ‘goal’ on it. Again, if you’re tying into an existing LizardFS system you’ll need to see how that’s configured before you go creating directories / setting goals in place.
If you’re running XenServer as it’s own LizardFS system we can do:
mkdir /mnt/lizardfs/xen-sr mfssetgoal 2 /mnt/lizardfs/xen-sr
Using a goal of “2” means (by default) that LizardFS will keep 2 copies (one on each node) of any chunks – so if one chunk server (XenServer fails) the other can still access the data.
Creating a storage repository (SR)¶
Now we need to create a XenServer Storage Repository (SR) on the LizardFS. If you have more than one XenServer – you should log into the pool master and then run:
Make a note of the pool master’s uuid (and the other nodes uuid) – you’ll need those in a moment.
export MYUUID=`uuidgen` xe sr-introduce uuid=$MYUUID name-label="LizardFS" content-type=user type=file shared=true 61625483-3889-4c55-8eee-07d14e9c9044 xe pbd-create sr-uuid=$MYUUID device-config:location=/mnt/lizardfs/xen-sr host-uuid=(uuid of pool master) 62c9a88a-5fe4-4720-5a85-44b75aebb7fd xe pbd-create sr-uuid=$MYUUID device-config:location=/mnt/lizardfs/xen-sr host-uuid=(uuid of 2nd node) a91b77ee-949d-49d9-186f-259cd96b5c00 xe pbd-plug uuid=62c9a88a-5fe4-4720-5a85-44b75aebb7fd xe pbd-plug uuid=a91b77ee-949d-49d9-186f-259cd96b5c00
At this point in XenCenter (the GUI admin tool for XenServer) you should be able to see a new storage repository called “LizardFS”
Ok – so we’ve now got a LizardFS system – and a XenServer Storage Repository.
At boot time – it’s obviously important that LizardFS is up and running ( either just the client, or the client – and server components if you’re running everything on XenServer).
The easiest way to achieve this (at present) is to create a startup script – and have that invoked, just before XenServer attaches to the LizardFS based storage repository. So we’ll edit a file called ‘/root/lizardfs-sr-start.sh’ – and put into it:
#!/bin/sh # Start the LizardFS 'master' Service (if you need to) service lizardfs-master start # Start the LizardFS 'chunkserver' Service (if you need to) service lizardfs-chunkserver start # Mount the LizardFS mfsmount /mnt/lizardfs # Return 'Ok' back exit 0
You need to ‘chmod u+x lizardfs-sr-start.sh’ to make sure it’s executable.
This needs to be hooked into the XenServer startup – this means editing one of the XenServer python files.
If you ‘vi /opt/xensource/sm/FileSR.py’ – and then search for a line that says “def attach” - you need to change that function to read:
def attach(self, sr_uuid): if not self._checkmount(): try: import subprocess subprocess.call(['/root/lizardfs-sr-start.sh'])
At boot time, as the local file repository gets attached – the ‘lizardfs-sr-start.sh’ script will be called – which makes sure the services are started, and LizardFS mounted up.
At this point you can test the system by restarting the 2nd node (if you have one) – then the first node (pool master) – both should come back, re-attach the LizardFS – and have the LizardFS storage repository available.
If you make one of your XenServer’s the meta-server master – it must be up and running in order for the other nodes to use the storage.
If the meta-server ‘master’ fails – you can promote one of the remaining ‘shadow’ servers to be the new master – but there must be only one ‘master’ on the system at any time (so the previous master will have to be reconfigured and come back as a ‘shadow’ server).
- LizardFS provide ‘lizard-uraft’ – which utilizes the raft
- protocol to keep a ‘master’ server always available. It’s designed for use by a minimum of 3 nodes (two of which can be the XenServer).
This is covered in Deploying LizardFS as a HA Cluster – along with ‘best practices’.
Having a third node also ensures there is always a ‘master’ server available for when the XenServer nodes boot. It is often common to need things like DNS, and ‘routing’ for XenServer to come up any way – so whilst you can build a 2 node system – 3 nodes is almost certainly better (even if one is not a XenServer – and just a basic machine providing DNS, LizardFS meta-server etc.)
Additionally – the third node can be used to provide a small amount of NFS storage. By creating a XenServer Storage Repository using this NFS space – XenServer’s HA (High Availability) mode can be enabled.
XenServer patches / updates may replace the modifications to the “FileSR.py” file – so remember to check this after installing updates.
Usually in a XenServer ‘pool’ situation you would update the master first (make sure that restarts OK – including the LizardFS side of things) – then update the other nodes in turn.
Using LizardFS for Virtualization Farms¶
If you want to use LizardFS as a back end for your virtualization Farm, there are multiple options.
- Use LizardFS from inside each VM
- The LizardFS client on Linux utilizes the FUSE library which has limits on the performance it can offer. To work around this one option would be to have each VM connect to the lizardfs system by itself. That way each VM has its own connection and gets the maximum performance possible via fuse.
- Create one mount point on your host for each VM (especially cool with KVM)
This is simple and efficient. Since the FUSE library creates a new instance for every mount point, each mount point gets the full performance of a FUSE connection and that way gets around the limits a single fuse connection currently has. So basically each VM, using a separate LizardFS mount point each, will get full throughput until the host runs out of network resources.
The setup is rather simple. Create multiple subdirectories in your LizardFS and mount each one separately for each VM:
mfsmount -S <lizardfs subdirectory> -c <mfsmount config file>
Best Practice for VMWare Networking¶
Currently only NFS is supported for connections from VMWare ESX Hosts.